Mission Furniture - LightNovelsOnl.com
You're reading novel online at LightNovelsOnl.com. Please use the follow button to get notifications about your favorite novels and its latest chapters so you can come back anytime and won't miss anything.
2 mirror-frame pieces, 3/4 by 2 by 20 in., S-2-S.
The following material list may be of common stock and not quarter-sawed:
Mirror-backing pieces equivalent to 1/4 by 18-1/2 by 36 in., S-2-S.
2 cleats, 3/4 by 2 by 10 in., S-4-S.
4 drawer-support frame pieces, 3/4 by 2 by 29 in.
7 drawer-support frame pieces, 3/4 by 2 by 15 in.
Slides taken from sc.r.a.p stock, 3/4 by 1 by 15 in.
3 back pieces, 3/4 by 2-1/4 by 28 in., S-2-S.
2 back pieces, 1/4 by 8 by 28 in., S-2-S.
8 drawer sides, 1/2 by 7-1/4 by 17 in., S-2-S.
2 drawer backs, 3/8 by 7 by 27 in., S-2-S.
2 drawer backs, 3/8 by 7 by 13 in., S-2-S.
2 drawer bottoms, 3/8 by 15 by 27 in., S-2-S.
2 drawer bottoms, 3/8 by 15 by 13 in., S-2-S.
In working up the various parts proceed in the usual manner. If not thoroughly familiar with the various tool processes involved, it will be necessary to investigate pieces of near-by furniture and to read up some good text dealing with the processes involved.
[Ill.u.s.tration: Dresser in Quarter-Sawed Oak]
The exact size of the mirror is 18 by 36 in. and the frame should be rabbeted to correspond.
[Ill.u.s.tration: Detail of the Dresser]
For a finish, a coat of paste filler colored so as to give a rich golden brown should be applied first. Allow this to harden, after rubbing and polis.h.i.+ng it in the usual manner, then apply a thin coat of sh.e.l.lac. Sand this lightly when hard, and over this apply a coat of orange sh.e.l.lac. Over the sh.e.l.lac put several coats of some good rubbing wax and polish each coat well. If a striking contrast is wanted for the medullary rays of the quartering, apply a golden-oak stain first. Sand this lightly, then apply a second coat diluted one-half with solvent and sand again lightly. Apply a thin coat of sh.e.l.lac, then, when dry, sand lightly and apply paste, and proceed as before.
A MISSION SIDEBOARD
Oak is the most suitable material for making this sideboard and it should be first-cla.s.s stock, planed and cut to the dimensions given in the following list:
1 top, 7/8 by 22 by 48 in., S-2-S.
1 top shelf, 7/8 by 12 by 48 in., S-2-S.
1 bottom, 7/8 by 22 by 48 in., S-2-S.
2 back posts, 2 by 2 by 57 in., S-4-S.
2 front posts, 2 by 2 by 36 in., S-4-S.
2 standards, 2 by 2 by 20 in., S-4-S.
2 mirror rails, 7/8 by 2 by 47 in., S-2-S.
2 mirror rails, 7/8 by 2 by 20 in., S-2-S.
3 front and back rails, 7/8 by 3 by 46 in., S-2-S.
4 end rails, 7/8 by 3 by 20 in., S-2-S.
4 standard rails, 7/8 by 2 by 10 in., S-2-S.
2 vertical pieces, 7/8 by 19-1/2 by 22 in., S-2-S.
1 horizontal piece, 7/8 by 22 by 14-1/4 in., S-2-S.
1 drawer front, 7/8 by 6 by 14-1/4 in., S-2-S.
1 piece, 7/8 by 3 by 3 in.
4 vertical door pieces, 7/8 by 2 by 17 in., S-2-S.
4 horizontal door pieces, 7/8 by 2 by 15 in., S-2-S.
2 drawer sides, 7/8 by 5 by 14 in., S-2-S.
1 drawer bottom, 1/4 by 14 by 14-1/4 in., S-2-S.
1 back panel, 1/4 by 16-1/2 by 44-1/2 in., S-2-S.
2 door panels, 1/4 by 10-1/2 by 15-1/2 in., S-2-S.
2 side panels, 1/4 by 18-1/2 by 16-1/2 in., S-2-S.
[Ill.u.s.tration: Detail of the Mission Sideboard]
Begin work by cutting the posts to the length indicated in the detail drawing. The top ends are tapered with a 1/2-in. slant. These posts are cut in pairs and it is best to stand them up in the same position they will be in the finished sideboard, and mark the sides to be mortised with a pencil. Also cut the grooves into which the panels are to fit.
These are to be 1/4 in. wide and a little over 1/4 in. deep.
[Ill.u.s.tration: Mission Sideboard in Quarter-Sawed Oak]
The rails are cut with tenon ends to match the mortises, and also have grooves to receive the panels.
The bottom part of the back is closed with a panel and two rails, one at the same height from the floor as the front bottom rail, and the top one even with the under side of the top. The large panel is for the opening thus formed.
These parts are now put together, using plenty of good hot glue, and spreading it well on the mortises and tenon ends.
When drawing the frame together with the clamps, care must be taken to get it square.
After the glue is hard enough to remove the clamps, the top and bottom are put in place. The corners of the top are notched out to fit around the posts, while the bottom is cut to fit on the inside of the rails and is held in place by putting screws in at an angle through the bottom into the rails. The top is also fastened in this way, except that the screws are run through the rails into the top.
The two vertical pieces are now put in place. Drive nails through the bottom and into these pieces. On the top end use screws driven at an angle. Glue may be used if desired.
The doors are made to match these openings. The corners are mitered and the backs rabbeted to receive the panels. These panels may be made in art gla.s.s if so desired.
The horizontal piece for the drawer to rest upon is now put in place and fastened by driving nails through the vertical pieces. The drawer is made to fit this opening, and it should be lined with velvet to keep the silverware in good condition.
The standards and shelves are put on as shown in the drawing. The mirror is put in a frame, which is made to fit the back opening and has the corners mitered and the back rabbeted to receive the mirror.
Thoroughly sc.r.a.pe and sandpaper all parts that are visible. The sideboard is now ready to be finished as desired.
A HALL OR WINDOW SEAT
[Ill.u.s.tration: Seat Made of Quarter-Sawed Oak]
A simple design for a hall or window seat is shown in the accompanying sketch and detail drawing. Anyone who has a few sharp tools, and is at all handy with them, can make this useful and attractive piece of furniture in a few spare hours. Quarter-sawed oak is the best wood to use in its construction, as it looks best when finished and is easy to procure. If the stock is ordered from the mill ready cut to length, squared and sanded, much of the labor will be saved. The following is a list of the material needed:
4 corner posts, 1-1/2 by 1-1/2 by 28 in., S-4-S.
2 side rails, 3/4 by 2-1/2 by 36-1/2 in., S-4-S.
2 end rails, 3/4 by 4 by 14-1/2 in., S-4-S.
2 side braces, 1 by 1 by 36-1/2 in., S-4-S.
2 end braces, 1 by 1 by 14-1/2 in. S-4-S.
