British Manufacturing Industries Part 5

_Rectangular plates, about 13 inches_ (0325 m.) _by 10 inches_ (0248 m.) _and 1/5 inch_ (0005 m.) _thick_.

These plates were allowed to fall flat on to a floor of wood or thrown to a distance and allowed to fall.

1 _Ordinary gla.s.s_ allowed to fall flat from a height of 1-2/10 inch (003 m.) was broken at the first trial.

2 _Toughened gla.s.s._ Thrown to a height 6 feet 6 inches (2 metres) and to a distance of 13 feet (4 metres) was also broken at the first trial. The piece, however, which had sustained the weight of 510 lb.

did not break till the fourth trial.

_Rectangular plates, about 10 inches_ (0245 m.) _by 6 inches_ (0157 m.) _and 1/4 inch_ (0007 m.) _thick_.

These plates were subjected to the same kind of tests as the foregoing. After raising them to a given height they were allowed to fall flat upon a wooden floor.

1 _Ordinary gla.s.s_ raised to a height of 20 inches (050 m.) was broken on falling.

2 _Toughened gla.s.s_ resisted successive falls of from 20 inches (050 m.), 32 inches (080 m.), 5 feet (150 m.), and 5 feet 7 inches (170 m.), but was broken when dropped from a height of 6 feet 6 inches (20 m.).

_Rectangular plates about 10 inches_ (0245 m.) _by 6 inches_ (0157 m.) _and 1/5 inch_ (0006 m.) _thick_.

Placed in the frames, they were held in position in the rabbets by laths nailed to the sides so as to prevent any play. The frames were raised to different heights and allowed to fall in such a manner as to cause as much vibration as possible.

1 _Ordinary gla.s.s_ was broken with a fall of about 2 feet (060 m.).

2 _Toughened gla.s.s_ resisted falls from heights of 3 feet 3 inches (1 metre), 6 feet 6 inches (2 metres), 8 feet (250 m.), 9 feet 9 inches (3 metres), and 14 feet 6 inches (450 m.). It was only broken by a fall of 19 feet 6 inches (6 metres).

_Rectangular plates 6 inches_ (0158 m.) _by 4-3/4 inches_ (0120 m.) _and 1/5 inch_ (0006 m.) _thick_.

These plates were placed in the frame on the ground, as has been previously explained. Known weights falling from known heights were made to strike the plates exactly in the centre. The weights consisted of bronze spheres, one weighing 3-1/2 oz. (100 grammes) and another of twice that weight.

1st. _Ordinary gla.s.s_ resisted the weight of 3-1/2 oz., falling from heights of 8 inches (020 m.), 12 inches (030 m.), 16 inches (040 m.), but was broken by a fall of 20 inches (050 m.).

2nd. _Toughened gla.s.s_ resisted the blow of the 3-1/2 oz. weight falling from heights of 20 inches (050 m.), 40 inches (1 metre), 60 inches (150 m.), and 6 feet 6 inches (2 metres). The 7 oz. weight (200 grammes) being subst.i.tuted, the plate was broken by it, falling from a height of 60 inches (150 m.).

_Rectangular plates, 6 inches_ (0158 m.) _by 4-3/4 inches_ (0120 m.) _and 1/6 inch_ (0004 m.) _thick_.

The same conditions were maintained as in the previous trial.

1st. _Ordinary gla.s.s._ The 3-1/2 oz. weight was allowed to fall from heights of 1 foot (030), and 16 inches (040 m). It was broken by the second blow.

2nd. _Toughened gla.s.s._ This resisted the 7 oz. weight falling from heights of 2 feet 4 inches (070 m.), and 2 feet 8 inches (080 m.), but broke when the weight fell from 39 inches (1 metre).

It appears then from these experiments, that toughened gla.s.s will resist a blow five times as great as ordinary gla.s.s, and will bear seven times as great a weight.

I have now detailed most of the useful experiments which have been made by competent observers upon toughened gla.s.s, as well as some which have been conducted in my own laboratory. The result of my own personal investigations I will now lay before the reader. I was consulted some time ago by a gentleman interested in the introduction of toughened gla.s.s into this country, as to whether this kind would become untoughened in time. I feel no hesitation in stating that when the process has been perfectly done, the gla.s.s will remain in the same state for any length of time, provided it be not treated in any way which is calculated to rupture the external hard bond that holds together the inner particles of the gla.s.s. I feel quite sure, that no fear of this kind need interfere with the benefits, whatever they may be, which are to be derived from submitting gla.s.s articles to the toughening process.

A tumbler which had been toughened in Monsieur de la Bastie's works, was, in my presence, thrown upon the ground, yet it did not break. It was a large soda water gla.s.s. I kept it for some time, and after considering the matter carefully, I felt, that if it were thrown down in such a way that the whole of its side, from base to rim, came in contact with the ground at once, and it then stood this test, it would prove that the whole of the gla.s.s was in the condition of the Rupert's Drops, and would therefore bear the concussion without fracture. I held the gla.s.s and let it fall, so that it actually reached the hard floor on its side. It immediately broke all to pieces. Now on the first occasion when this gla.s.s was thrown down, it was tossed somewhat upwards into the air, and the bottom being heavier reached the ground first, and it did not break. I have also seen in gla.s.s-houses, where the tempering process is carried on, tumblers thrown down in a similar manner, and I noticed, that whenever they fell upon their bottoms, they were uninjured, as also in cases where they fell upon their rims in such a manner, that the curve of the rim acted as an arch, as in the old trick of turning a wine-gla.s.s off the table so as not to break; but in other cases where the tumblers fell flat upon their sides, fracture followed. I carefully gathered together the pieces of the large tumbler which I broke myself in this manner, and examined them, and found that the solid bottom was broken in the same manner as the Prince Rupert's drops break, viz., into a large number of small pieces, having in all respects similar properties. The gla.s.s for an inch or two above the bottom broke into small pieces, but larger than those into which the bottom itself broke, and the upper portion of the tumbler was fractured just as an ordinary tumbler would be. On careful examination, microscopic and otherwise, the small pieces were found to have the character of Prince Rupert's, whereas the larger from the upper part of the gla.s.s had none of these characteristics in the slightest degree.

These observations led me to perform an experiment. A toughened tumbler was filled with plaster of Paris, which was allowed to set.

Its outside was then encased in plaster of Paris, and when the whole was hardened, a pair of pincers were applied to a portion of the tumbler's rim, and with a violent wrench the tumbler was broken. A rather smart shock was communicated to the arm of the operator, very much resembling, as he said, the shock of an electrifying machine. On removing the plaster of Paris, it was found that the whole of the tumbler was fractured, and, as will be seen by the accompanying ill.u.s.tration, in a manner similar to that which has already been described.

From this and other similar experiments, I was led to the conclusion that none of the toughened articles which have cavities in them, have thoroughly undergone the toughening process.

Having been requested to attend a series of experiments performed by a gla.s.s manufacturer in London, which consisted in the manufacture of a number of toughened gla.s.s tumblers, I noticed certain facts which led me to form conclusions as to how it was that the tumblers, the fracture of which I already explained, break in this peculiar manner.

I will first describe the way in which these tumblers were made and toughened. By the side of the gla.s.s blower there stood a metal vessel, about three feet six inches high, and, perhaps, from two to two feet six inches in diameter. This was filled with melted fat or oil of some kind at a temperature of about 80 Fahr. Inside this vessel, which was open at the top, there was a wire cage, with a trap door at the bottom about one foot in diameter, and of about the same depth. The gla.s.s blower, after finis.h.i.+ng his tumbler on the pontil, held the pontil in a horizontal position over this metal vessel, struck it a smart tap, and the gla.s.s tumbled off into the wire cage. The gla.s.s was at a very high temperature. In almost every instance the gla.s.s fell into the melted fat, as a gla.s.s thrown in a similar manner will fall into water. It sank gradually bottom downwards, and the liquid guggled into it as it sank. Here, then, it is clear that every portion of the hot tumbler did not come in contact with the oil at the same moment, in fact there was an appreciable lapse of time before the tumbler disappeared beneath the surface of the liquid. Now there must be a limit as to the temperature of the article to be tempered and of the liquid by which it is to be tempered, that is to say, if at a certain temperature gla.s.s can be tempered by being plunged into the liquid of a certain temperature, if these temperatures are varied similar results will not follow. The upper portions of the gla.s.s coming in contact with the tempering liquid at a lower temperature, as they must have done, were not properly tempered, and this I have clearly proved by the facts I have already stated. From these remarks it seems tolerably clear that, until some method is devised of bringing all the parts of the heated gla.s.s in contact with the cooling liquid simultaneously, the tempering of the article cannot be perfect throughout its whole surface. As I desire, and very sincerely, that these processes should be brought to perfection so as to render them useful, I willingly give this result of somewhat lengthened investigations to those whom it may commercially concern, and I hope that they will find, on investigating the matter, that my observations have been tolerably correct, and that they will be able to devise a method which will remedy in many cases manifest imperfections of their present system. All the accidents which have happened to tempered gla.s.s, which have been recorded in the newspapers, can be accounted for on the principle which I have just endeavoured to explain, for there must be instability, where the bonding material of the internal particles of the gla.s.s is in different states of hardness; so that there is no difficulty in conceiving how a gas globe could break apparently spontaneously, for a portion of it which was not fairly toughened might be exposed to a somewhat sudden rise of temperature, produced, it may be, from a draught blowing the flame upon that particular spot. Articles such as saucers, made of gla.s.s, which, being flat, or nearly so, can be plunged into the tempering liquid with great rapidity, are usually tempered all over, and these, when toughened, can be thrown about and allowed to fall on hard floors with impunity, thus proving the facts which I have endeavoured to establish. I hope to be able to continue my investigations, and should they be worth anything, will give the results of them to the public.

Before quitting this subject, I shall make a few remarks upon the process for toughening gla.s.s, which is said to have been purchased by the Prussian Government.

This process is described as consisting in the application of superheated steam to the gla.s.s, brought up to a temperature near to its melting point. Having facilities for making experiments of this kind, I have had them tried with great care, but in no case have I met with a satisfactory result. This probably is owing to the fact, that I did not comply strictly with the condition of the experiments performed by the German chemist who is said to have made the invention, nor do I see from a.n.a.logy how this process is likely to effect a change in the gla.s.s similar to that arising from M. de la Bastie's dipping process.

If gla.s.s, instead of being taken from the annealing kiln at the proper time, be left exposed in the hot part of it, at a temperature just below that at which it softens, it will be found to become gradually opaque on its surface. Some experiments were performed many years ago by Reaumur, who exposed pieces of gla.s.s, packed in plaster of Paris, to a red heat, which became gradually opaque, and lost altogether the character of gla.s.s, the texture of their material becoming crystalline, and also effected by sudden changes of temperature. Gla.s.s treated in this way was called Reaumur's porcelain. All gla.s.ses do not undergo this change with equal rapidity, and some do not experience it at all; but the commoner kinds, such as bottle gla.s.s, are the best to experiment upon, for the more alumina that it contains--and it is known that bottle gla.s.s contains a considerable quant.i.ty--the more readily does it undergo this change, which is called _devitrification_.

In what it consists, is not at present well understood, but it offers a field for investigation, which may produce results of very considerable benefit to manufacturers of gla.s.s.

_Soluble Silicates._--An article on gla.s.s in a modern scientific work like the present would not be complete without a notice of the manufacture of soluble gla.s.s and the uses to which it has been and may be applied. It has already been mentioned that when silica or sand is fused with an excess of alkali, the resulting gla.s.s is soluble in water.

Soluble gla.s.s is made on a large scale in three different ways. First of all, if flints, that is, black flints, which are found in chalk, be heated to a white heat, they lose their black colour and their hardness, and are easily crushed to small pieces; and if flint in this condition be placed in a wire cage and put into a jacketed iron digester, that is, an iron digester which has an inner and an outer skin, with a free s.p.a.ce between the two, so that steam may be forced into it from a boiler under pressure; and if the digester be screwed down tightly with an iron cover, and steam then be allowed to pa.s.s into the s.p.a.ce between the two, the temperature can be raised at pleasure, according to the pressure under which the steam is introduced. If the valve of the boiler be loaded with a 60-lb. weight, the temperature of the water warmed by the steam will rise considerably higher than that of ordinary boiling water; and if this water be saturated with caustic soda, it will dissolve the flints slowly, forming silicate of soda, that is to say, the silicic acid of the flint will unite directly with the soda of the solution, and silicate of soda will thus be obtained. For certain applications, the silicate so formed is not sufficiently pure, because the soda used often contains a certain amount of sulphate, which will remain with it in the solution of silicate that is drawn off from the digester. This sulphate is very objectionable for certain applications of silicates, because it crystallizes out, and so destroys the substance, which the silicate is intended to preserve.

Another and a much better method is to heat together the silica in the form of sand with alkali, either potash or soda, in a reverberatory furnace, and as the gla.s.s becomes formed, to rake it out into water, and then gradually to dissolve it by boiling in suitable vessels. Here the sulphate, if it existed in the alkali, is decomposed by the silicic acid, and the sulphuric acid pa.s.ses off through the flues of the reverberatory furnace.

There is also a very ingenious way of making silicate of soda, discovered by Mr. Gossage, and performed as follows: common salt is heated to a high temperature and volatilized, and in this condition is brought into contact with steam also at a high temperature, when a double decomposition takes place. Steam is composed of oxygen and hydrogen; common salt, of sodium and chlorine. The chlorine of the common salt unites with the hydrogen of the steam, and the oxygen of the steam with the sodium, so that hydrochloric acid and oxide of sodium are formed. Now, if these two substances at this high temperature were allowed to cool together, the action would be reversed, and the re-formation of steam and chloride of sodium would be the result; but in the strong chamber lined with fire-clay, in which these vapours are brought into contact, silica is placed in the form of sand made up into ma.s.ses, and when the oxide of sodium is formed, it unites with the sand to make silicate of soda, and thus is removed from the action of the hydrochloric acid, not entirely, but sufficiently to produce a large yield of silicate of soda.

The properties of silicate of soda, as applied to the arts, are somewhat different from those of silicate of potash, so that one cannot always be subst.i.tuted for the other. Both these substances are, when in solution and concentrated, thick and viscid, and have the property of causing paper, wood, &c., to adhere when applied as a gum or glue, and hence have been called "mineral glue." In a dilute state they can be used for coating stone, brick, or cement, and have the power of rendering them for a time waterproof, or nearly so, and of preventing the action of atmospheric influences, which too often produce the decay of some of the softer stones used for building as well as for cement. It has already been stated, that when carbonic acid is pa.s.sed through a solution of silicate of soda, silica will be precipitated. Now, inasmuch as there is carbonic acid in atmospheric air, when these solutions are applied to the surfaces of a building, they will be acted upon slowly by the acid, and silica will be precipitated in the pores of the material to which the silicates are applied. But this operation is extremely slow, and, before it can be thoroughly completed, the silicates, being soluble, will get in part dissolved out by rain and moisture, and it is therefore advisable to use with them some material which will, by a double decomposition, form a silicate insoluble in water. The silicate, however, which is formed, should have cohesion amongst its particles, so that it will not only adhere to the stone itself, but its own particles will adhere to one another when it gets dry. Various methods have been tried to cause this insoluble substance to be formed upon the surface of stones, so as to fill up its pores and to make a protecting cover for it; but most of them have signally failed, because the new silicate produced by double decomposition has not had the necessary coherence amongst its particles. If a solution of chloride of calcium be added to one of silicate of soda, a silicate of calcium will be precipitated, and it was therefore thought, that by applying to a stone successive washes of silicate of soda and chloride of calcium, an insoluble silicate of calcium would be produced in the pores and on its surface. It is true that such a silicate is precipitated, and that, if the silicate employed be in excess of the chloride of calcium, the particles will be glued together by the adhesive powers of this silicate when it dries; but then the action of moisture upon it is to cause it to run down the surface of the building, and set free the particles of silicate of calcium which it held in combination. Other processes of the same kind have been tried, and with similar results; one great difficulty in the way of the success of this method of applying silicates being that, from the peculiar colloidal or gluey nature of the silicate, it does not penetrate to any considerable depth into the stone, and, if laid on first, prevents the penetration, as far even as it has itself gone, of the solution of chloride of calcium. If the chloride of calcium be used before the silicate, it will penetrate farther than the solution of silicate is able to reach, so that it is impossible to obtain, even supposing the substance to be used in equivalent proportions, a complete decomposition of the one by the other.

The great object to be attained in the preservation of stone by any silicious process, is to use _one_ solution possessing the substances which, when the water has evaporated, will form a perfectly coherent ma.s.s for the protection of the stone surface. The depth of penetration, if it is sufficient to protect the outside of the stone from the disintegrating action of the atmosphere, need not be carried much more than one-sixteenth of an inch below the surface, for when old stones which have long been in positions in buildings, and which have not decayed at all, are examined, it will be found that they are covered with an extremely thin film of a hard substance, not thicker than a sheet of writing paper, which has for ages protected and preserved them from decay. This film is produced by a determination from the inside to the outside of the stone of a silicious water, which existed in it in the quarry, and which, when the stone was placed in the building, gradually came to the surface, the water evaporating and leaving behind it a thin film of silica, or of a nitrate--most likely the latter.

If alumina be fused with potash, aluminate of potash, soluble in water, is made; if, however the solution is too concentrated, a certain quant.i.ty of the alumina will be precipitated; but if it be dilute, the whole of the alumina will remain in solution. When aluminate of potash of specific gravity 112 is mixed with a solution of silicate of potash of specific gravity 12, no precipitate or gelatinization will take place for some hours; the more dilute the solution, the longer will it remain without gelatinization, and of course the thinner it will be, and the greater power of penetration it will have when applied to a porous surface. When solutions of aluminate of potash and of silicate of potash of greater density are mixed together, a jelly-like substance is almost immediately formed, and sometimes even the whole ma.s.s gelatinizes. If this jelly be allowed to dry slowly, it will contract, and at last a substance will be left behind sufficiently hard to mark gla.s.s, though the time for this hardening may be from one to two years; and on examination it is found that this substance has very nearly the same chemical composition as felspar, and is perfectly insoluble in ordinary mineral acids. Now, suppose a dilute solution of this mixture to be applied to the surface of stone, the silicate and aluminate of potash will gradually harden and fill up the interstices of the stone; and as both the substances entering into combination are contained in the same solution, they will both penetrate to the same depth. Inasmuch as the artificial felspar is not acted upon by destructive agents which would disintegrate the stone, it becomes a bonding material for its loosened particles, and at the same time gives a case-hardening to the stone, which no doubt will as effectually protect it against atmospheric influences as in the case of the hardening of the natural one. We have a tolerable guarantee that this will be so, if we consider the number of enduring minerals into the composition of which silica, alumina, and potash enter, and also of the almost imperishable character of granite, which is so largely composed of felspar. Many experiments have been performed on an exhaustive scale with these materials, and in every case it has been found that they have answered the expectation of those who have thus tested them. It is, however, necessary to state, that in making these experiments, great care must be used to employ the mixed substance in solution before gelatinization has set in, for if this has occurred, even to the slightest extent, a surface coating is formed on the stone, which, not having formed a bond with it, easily rubs off.

Another application of soluble silicates in this or other forms is to render walls of buildings which are porous, waterproof. A colourless, transparent material which can effect this object is doubtless desirable, as anything like an opaque wash, if applied to brick-work, would destroy the colour of the bricks, and therefore the character of the building constructed with them. The silico-aluminate of potash may be used for this purpose, as above directed; and even silicate of potash alone, provided it be in sufficient quant.i.ties, will answer well, if from year to year, for two or three years, the application be renewed, so as to fill in s.p.a.ces, wherever the silicate may have been in part dissolved out. When the silicate of potash alone is used, the action of the carbonic acid of the air in precipitating the silica is depended on, and while this action is going on, portions of the silicate not acted on will be dissolved out.

Many years ago, an effort was made in Germany to revive the ancient art of fresco painting, and with very considerable success. It was found, however, that our climate is not suited to the permanence of this method of decoration, nor indeed is any climate absolutely suitable, because in fresco painting, the surface only of the lime is coloured with pigments laid on, so that any influence which would destroy the lime surface would cause the removal of the pigments; and from the porous nature of the surface of the work after it is completed, absorption of moisture will from time to time take place, causing the adhesion of dirt and other foreign substances which may fall upon it, and which it is almost impossible to remove without detriment to the picture. Dr. Fuchs, of Munich, discovered a method of painting with soluble silicates, which has been tried with considerable success in Berlin by the late Professor Kaulbach. On a properly prepared ground, the painting was executed in colours mixed with water, which, when dry and the painting finished, were fixed to the wall by the application of soluble silicates. For the preservation of the work, Dr. Fuchs mainly relied upon the action of atmospheric carbonic acid. Now, when carbonic acid acts upon silicate of soda or silicate of potash, we have already seen that the silicic acid is precipitated in the hydrated form, and that the carbonic acid has united with the soda or potash to form carbonate of soda or carbonate of potash. These substances being left in the painting and penetrating to a certain depth beneath its surface, must find their way out, and in almost every instance have done so in the form of an efflorescent substance, which has caused the picture to have the appearance of being mildewed over its surface. Sometimes, however, sulphates occur in the ground, and then sulphates of soda and of potash have been formed, injurious to the permanence of the surface of the picture, because they crystallize and force off portions of the lime and sand of which the surface is composed. The effect of the efflorescence of the carbonates on the surface of a silicious painting may be seen in the famous picture of the meeting of Wellington and Blucher, in the House of Lords, painted by the late Mr. Maclise, R.A. When, however, the solution of aluminate and silicate of potash is used with the pigments on a properly prepared ground, there is no fear of this efflorescence taking place, and paintings executed with it have stood for many years, without giving any signs whatever of decay.

To those interested in this subject, it is desirable that they should perform a series of experiments themselves, and ascertain the best methods of practically applying this vehicle in the execution of large mural paintings. They will find that, although at first they may meet with some difficulties, yet after a while these difficulties will vanish, and they will have a material to work with, which will meet all their requirements.

In an article so brief as the present, it is impossible to enter fully into all the details of the manipulation of this particular process of painting; it is, however, most desirable to give a short account of the method of preparing the ground and of applying the colours, leaving the rest to be learned from practical experience.

Angular fresh-water river sand, well washed, should be mixed with sufficient lime to cause it to adhere to the wall on which it is placed, and this in all cases should be freshly plastered in the ordinary way. No plaster of Paris (which is sulphate of lime) should be used in the preparation of the groundwork. The coating of fine sand and lime is laid on to a depth of about an eighth of an inch, and when dry, an application of dilute silicate of potash should be made, in order to bond together the particles of sand which, owing to the employment of so small a quant.i.ty of lime, can be readily brushed off.

As soon as these particles are well fixed together and do not come off when the hand is pa.s.sed over the surface of the wall, the ground is in a fit state for the commencement of the painting. The colour should be used with zinc white, and not with lead white, and, of course, they must be in the state of fine powder, and not ground up with oil or any such material. The artist can use his mixture of silicate of alumina and aluminate of potash of the strength already described; he may, when desirable, dilute it to a certain extent with water, but he should not do so too much. He can then paint with it just as he would with water in water-colour painting; and if he finds that any portion of his colours, after they are dry, are not sufficiently fixed upon the wall, he can then with a brush pa.s.s over them a coating of the clear liquid, used a little stronger. When the whole work is finished, it will perhaps be desirable to give it one or two coats of a very dilute solution of silicate of alumina and aluminate of potash. After a time, owing to the contraction in drying of this material, it would be advisable--say, after the lapse of two or three months--to again apply a coat of it somewhat stronger; and again, if after a year, or more than a year, it should appear that any portions of the surface were becoming loose, another application of the mixed silicate of alumina and aluminate of potash to these loosened parts alone will be desirable. This repet.i.tion may appear to some to be an objection to the process, but it is not so, however; for in the formation of those natural substances, such as flints, which we find so hard, no doubt a very great lapse of time occurred in the induration of the gelatinous silica which formed them. Neither do we object from time to time, at intervals of years to renew the coats of varnish on oil paintings, in order to preserve them or to bring out afresh the brilliancy of their colours.

The soluble silicates are frequently used as bonding materials in the manufacture of artificial stone and cement, very good results having been attained. The objection, however, to their employment for these purposes is the expense of the material of which they form a const.i.tuent part, and it seems almost impossible ever to bring it into compet.i.tion with dressed natural stone. But for ornamental purposes, from the plastic nature of the substance when in the wet state, it can be pressed into moulds, and wherever plaster mouldings are admissible, no doubt this material would be useful for certain kinds of ornamentation. Some years ago, Mr. Ransome, of Ipswich, after having made his artificial stone with sand and silicate of soda, heated it in ovens, so as to produce a hard and semi-vitrified ma.s.s. A church, the mouldings of which are made of this stone, may be seen at the bottom of Pentonville Hill, London; and certainly as to durability, there is no doubt that the substance has answered very well. But from difficulties in manipulation and other reasons, that gentleman gave up this method of making artificial stone, and is now working another process which yields far better results. Silicate of soda is mixed with sand (generally Aylesford sand), and after the mixture is moulded and dried, it is exposed to the action _in vacuo_ of chloride of calcium in solution. Whether the whole ma.s.s is placed in a vacuum chamber and then charged with chloride of calcium; or whether a vacuum is formed on the under side of the substance, and the chloride of calcium solution caused by suction to filter through it, is uncertain.

However, whatever be the manipulative processes, the result is the same, and appears to be extremely satisfactory.

Soluble silicates produce very remarkable results when mixed with certain substances. If silicate of soda or potash be mixed with white lead, in a very short time it sets into a hard substance, just as does plaster of Paris when mixed with water. If powdered pumice-stone or sand, in the proportion of eight parts to one of carbonate of lead, be mixed together with soluble silicate, a very hard and coherent ma.s.s is obtained, and there seems no reason why a mixture of this kind, in which pumice-stone is used, should not be employed for the purpose to which pumice-stone is usually applied. It would have the advantage of being easily moulded into forms, so as to suit mouldings, which might by it be much more accurately and expeditiously smoothed down (as in the case especially of picture-frame mouldings), than they can be by the ordinary pumice-stone.

Another very important application of soluble silicates is the rendering of wood incombustible. Many experiments have been performed which show that when wood is thoroughly impregnated to a depth of a quarter of an inch or more with silicate of soda, it will not flame, but will only char. Now, supposing that the constructive timbers of a house were worked, and then placed in suitable vessels and saturated with silicate of soda, they would then be rendered practically fireproof, or at least it would take a very prolonged exposure to heat to cause them to smoulder away, while at no period of this time would they burst into flame. From the peculiarly gluey nature of these soluble silicates, they do not penetrate readily into porous substances; it has therefore been suggested that the impregnation of the wood should take place in vacuum chambers, just in the manner that the creosoting process for preserving railway sleepers is at present performed. It is most certainly advisable that the wood should be worked before being exposed to the silicating process, for that would render it so hard, that it would considerably increase the cost of labour in cutting and planing it.

At the commencement of this article, it was stated that silicic acid, or silica, could be made soluble in water. Some very interesting experiments were performed by the late Dr. Graham, Master of the Mint, which gave rise to the discovery of the process of dialysis. If some silicate of soda be mixed with water, so that not more than 5 per cent. of silica be in the solution (rather less is better), and if some hydrochloric acid be then added in sufficient quant.i.ty to make the liquid distinctly acid, and the mixture be placed in a dialyzing apparatus, the chloride of sodium formed by the union of the chlorine of the hydrochloric acid with the sodium of the silicate of soda will pa.s.s out through this dialyzing membrane, leaving hydrated silica behind, which will remain in solution in the water with which the silicate was mixed. The dialyzing apparatus is constructed in the following manner; a sort of tambourine ring is made with gutta percha, in place of wood, from 8 to 10 inches or even more in diameter, the depth, being about 2 inches. Another ring of gutta percha, of about an inch deep or even less, is made so as to fit tightly outside the tambourine; a piece of vegetable parchment is then moistened and placed over the tambourine, and the thinner ring is pressed over it, so as to secure it tightly. This is the dialyzing vessel, and it is into this that the mixture of silicate and hydrochloric acid must be put. The solution should not be more than an inch deep in the dialyzing vessel, which is then made to float upon distilled water in a larger vessel of suitable size. The distilled water should be changed every day, until no precipitate can be obtained in it with nitrate of silver, and when this point is arrived at, all the chloride of sodium will have pa.s.sed through the vegetable parchment into the larger vessel of water, and nothing but silicic hydrate will remain behind in solution. If this liquid be allowed to stand for some time, it will gelatinize, and later on the jelly will contract, becoming extremely hard, so that lumps of it, when broken, will in their fracture resemble that of flint. No doubt, at some future period, some one will discover a method of rendering this condition of silica useful in the arts.

Soluble silicates are very useful as detergents. A small quant.i.ty of silicate of soda mixed with hard water renders it valuable for was.h.i.+ng purposes. Silicate of soda is also used in the manufacture of the cheaper kinds of soap. We can hardly speak of it as an adulteration, because it renders the soap with which it is combined much more powerful in its cleansing action. I suggest to those interested in the application of science to the arts, that this subject will no doubt well repay experimental investigations.

It is much to be wished that those engaged in this branch of art and manufacture, and who have some knowledge of chemistry, would turn their attention to getting a better and more perfect method of making coloured pot-metal gla.s.s. I have been engaged for some time, and still am engaged, in experiments to effect this object. But inasmuch as my engagements are very numerous, and I cannot give the proper time to it I desire, I therefore take the liberty of suggesting to others the ways in which I am working, that they may be able to arrive at good results more speedily probably than I shall be able to do. If sulphate of copper be mixed with silicate of potash, silicate of copper will be precipitated. Now, if this be carefully washed and dried, it will be a silicate of a definite composition, and I propose to use such silicates as these with ordinary gla.s.s mixtures, in order to impart the particular colour which the oxide employed has been already described as giving to the gla.s.s. Silicate of manganese is prepared in a similar way to the silicate of copper; silicate of cobalt, and other silicates, can be used as staining materials for colouring gla.s.s.

These mixed in due proportion would give tints, and would, I do not feel the slightest doubt, produce colours with much greater certainty than they are now produced, and tints. .h.i.therto unknown could be made to the great benefit of the gla.s.s-painter.